FOR SURVEYING AND MONITORING COMPANIES

Bridge deformation monitoring for small and medium bridges

Measure the set-up once with your own total station, then leave TotaLite behind for continuous, millimetre-accurate data. No automated total station on site.

TotaLite sensor for bridge deformation monitoring on a small masonry bridge

Bridge deformation monitoring

Prism displacement (mm)
PrismdXdYdZ
P10.42-0.180.09
P2-0.310.26-0.04
P30.12-0.370.15
P4-0.560.41-0.12
P50.280.080.06
P6-0.19-0.22-0.03

Timestamp: 11/21/2026, 2:28:20 AM

Under 1 hour

to install

25 prisms

measured at once, up to 70 m

Up to 65%

lower project cost

Up to 70%

fewer manhours

THE PROBLEM

Small bridges need monitoring that nobody can afford to staff

29% of 35,260 communal bridges in France are in significantly poor condition.

Cerema, 2025

Most small bridges are too small to justify a $70,000+ automated total station. So they get a manual survey every few months, and movement between visits goes unseen until it’s expensive to fix.

HOW IT WORKS

How the bridge monitoring system works

01

Measure your prisms with your total station. Your coordinate system stays the same.

02

Mount TotaLite in under an hour. The mobile app guides you; no laptop or cables.

03

Take your total station to the next job. TotaLite measures every prism at once, every 5 minutes.

04

Get alerts when the bridge moves. Go back to site only when you need to.

Is TotaLite right for your bridge? Small bridge monitoring checklist

✓ All points to monitor are within 70 m of one TotaLite device position
✓ The TotaLite device has a clear line of sight: 60° × 45° field of view
✓ The bridge needs monitoring quarterly or more often
✓ An ATS would be too expensive, or too likely to be stolen

Typical projects include ageing masonry and Victorian bridges, bridges next to construction, load tests, and monitoring before and after repairs. For long-span bridges, use several TotaLite devices or an ATS.

Check if your bridge qualifies

WHY SURVEYORS CHOOSE TOTALITE

Built to be left on site

Fits your workflow

Anchored to your total station survey and reported in your coordinate system. Your deliverables don’t change.

All prisms at once

One image captures every prism in view, so load-test readings are truly simultaneous.

No recalibration

No moving parts. Temperature-stable diffractive optics replace servos and motors.

Corrects its own movement

Fixed reference points and an on-board accelerometer keep data reliable on structures that flex.

No site infrastructure

No pillar or mains power. Runs on 4–6 Wh from a battery, with optional solar, over SIM or ethernet.

Unattractive to thieves

Small and cheap to replace, unlike a €45,000 instrument left on a bridge overnight.

TotaLite vs automated total station vs manual monitoring

DATA — TotaLite: continuous, every 5 min · ATS: continuous · Manual: one snapshot per visit
EQUIPMENT COST — TotaLite: about 10× lower than ATS · ATS: $70,000–100,000 · Manual: low
SET-UP — TotaLite: under 1 hour · ATS: days · Manual: every visit
SITE INFRASTRUCTURE — TotaLite: none · ATS: pillar, power, control box · Manual: none
PROJECT COST — TotaLite: up to 65% lower than manual · ATS: highest · Manual: about 3× TotaLite

Branston Bridge: a 186-year-old bridge, monitored 24/7

Terra Measurements monitors this Victorian bridge in Staffordshire, UK, with one TotaLite device and 7 prisms. Weekly site visits are no longer needed.

65% lower project cost · 70% fewer manhours · 24/7 stability insight

Bridge displacement monitoring specifications

Accuracy — Millimetre-level, up to 70 m
Targets — Up to 25 standard prisms, 17 mm / 0.7 in or larger
Measurement interval — Every 5 minutes
Installation — Under 1 hour, mobile app
Field of view — 60° horizontal, 45° vertical
Power — 4–6 Wh; battery, optional solar
Connectivity — Built-in SIM (LTE) and ethernet
Per bridge — TotaLite device and bracket, prisms, monthly platform subscription

Bridge deformation monitoring FAQ

What is bridge deformation monitoring?

How does TotaLite work with my total station?

Can TotaLite capture deflection during a bridge load test?

How is TotaLite powered on a remote bridge?

What are TotaLite’s limits?

Bring continuous monitoring to every bridge that needs it

Send us your bridge’s span and sight lines. We’ll confirm the fit and compare the cost with your current approach within two working days.

CUSTOMER PROOF

Proven in the Field: The Branston Bridge

A typical example of our technology in action is the monitoring of Branston Bridge, an 186-year-old Victorian structure in Staffordshire, UK. Terra Measurements used TotaLite’s solution to monitor the behavior of 7 targets on the structure.

TotaLite sensor monitoring a Victorian bridge
Close-up of a TotaLite sensor lens

65%

cost reduction by eliminating weekly site visits

70%

fewer man-hours and associated travel emissions

24 / 7

continuous insight into structural stability

Read the full case study →